"AOX-Q-L" series high speed automation electric linear actuator is a product developed by AOX. We have a group of passionate and innovative high-quality R & D personnel. From the initial design, material selection, process determination, exquisite manufacturing methods, and rigorous testing processes, we ensure that each AOX product can meet the most stringent operating conditions.
"AOX-Q-L" series high speed automation electronic linear actuator is a product developed by AOX. We have a group of passionate and innovative high-quality R & D personnel. From the initial design, material selection, process determination, exquisite manufacturing methods, and rigorous testing processes, we ensure that each AOX product can meet the most stringent operating conditions.
The power supply wiring of "AOX-Q-L" series High Speed Automation Electric Linear Actuator needs to be configured as follows: 1. Remove the aluminum metal plug for external cable access. Please use 3 / 4 external thread Explosion proof connector or explosion-proof cable hose. 2. If the cable joint does not meet the requirements of the actuator, the sealing level inside the machine may be lowered to meet the protection requirements, or the water inside the actuator may damage the machine. 3. Waterproof measures shall be fully taken when using wire conduit. 4. Disassemble the casing cover. Press down the metal spring piece in the small hole on the terminal with a screwdriver. At the same time, the wire is smoothly inserted into the side wire insertion hole. Pull out the screwdriver and the wire is reliably clamped by the spring clamping mechanism inside the terminal
Force range: |
2000 - 40000 N |
|
Max stroke: |
100 mm |
|
Running speeds: |
0.33 mm/s - 1 mm/s |
|
Ambient temperature: |
-25 °C +70 °C |
|
Corrosion level: |
Epoxy powder coating. NEMA 4X corrosion protection |
|
Anti-vibration level: |
JB/T 8219 |
|
Noise level: |
Less than 75 dB within 1 m |
|
Ingress Protection:: |
2* NPT 3/4 |
|
Electrical interface: |
IP67, Optional:IP68 |
|
On/off type signal:
|
Input : AC 110/220 Input Signal Feedback:Integrated fault contacts,Close the valve contact,Open the valve contact |
|
Modulating type signal:
|
Input signal: 4 - 20 mA; 0 - 10 V; 2 - 10 V Output signal: 4 - 20 mA; 0 - 10 V; 2 - 10 V Loss Signal Mode Setting:N/A Dead Zone:≤2% |
|
Time Lag: |
N/A |
|
Shell: |
Enclosure :IP67,NEMA4, Exd II CT5 |
|
Power: |
Standard:220VAC/1ph Optional:110VAC/1ph, 380V/440V/3ph,50/60Hz, ±10% 24VDC/110VDC/220VDC |
|
Motor: |
Asynchronous motor |
|
Limit switch: |
2×Open/ Close, SPDT,250VAC 10A |
|
Torque switch: |
Close/Open, each 1, SPDT,250VAC 10A |
Except AOX-QL-20/30/50/80 |
Model |
Thrust |
Speed |
Max travel |
power |
Rated current(A) 50HZ |
Weight |
|||
Single-phase |
Three-phase |
||||||||
N |
mm/S |
mm |
W |
110V |
220V |
380V |
440V |
Kg |
|
AOX-Q-L20 |
2000 |
0.66 |
60 |
20 |
1.10/0.95 |
0.55/0.54 |
0.30/0.30 |
N/A |
18 |
AOX-Q-L30 |
3000 |
0.66 |
60 |
20 |
1.10/0.95 |
0.55/0.54 |
0.30/0.30 |
N/A |
18 |
AOX-Q-L50 |
5000 |
0.66 |
60 |
20 |
1.10/0.95 |
0.55/0.54 |
0.30/0.30 |
N/A |
18 |
AOX-Q-L80 |
8000 |
0.33 |
60 |
20 |
1.10/0.95 |
0.55/0.54 |
0.30/0.30 |
N/A |
18 |
AOX-Q-L100 |
10000 |
0.50 |
60 |
40 |
1.65/1.67 |
0.88/0.84 |
0.31/0.31 |
0.30/0.31 |
30 |
AOX-Q-L160 |
16000 |
0.50 |
100 |
40 |
1.67/1.67 |
0.89/0.85 |
0.31/0.31 |
0.30/0.31 |
32 |
AOX-Q-L200 |
20000 |
0.44 |
100 |
90 |
1.85/1.86 |
0.92/0.92 |
0.35/0.35 |
0.34/0.34 |
33 |
AOX-Q-L250 |
25000 |
0.44 |
100 |
90 |
3.60/3.62 |
1.55/1.58 |
0.59/0.59 |
0.58/0.58 |
34 |
AOX-Q-L300 |
30000 |
0.44 |
100 |
90 |
3.65/3.62 |
1.60/2.20 |
0.60/0.59 |
0.59/0.59 |
35 |
"AOX-Q-L" series High Speed Automation Electric Linear Actuator valve position detection mechanism
Through the rack directly connected to the output shaft and the two sets of gears of the control mechanism, the real-time position and the fully open and fully closed position of the valve can be independently detected to maximize the accuracy and safety.